Xiamen yitai industrial co., Ltd

Four , Attention.

1. 
   No hit or scrap on the cutter to avoid damage the cutter.
   
2. 
   The whole machine is debugged before shipping, so pls do not unstall any parts of the machine。
   

Five, Machine adjusting and cutter exchanging.

1. 
   The cutter constructed by 4pcs and installed on each cutting mold.In order to ensure install correctly, pls do it one by one.
   
2. 
   It requires three blade positioning surface to locate, but only two positioning surfaces on the cutting die, both the bottom and back. So the key of the key blade is installed; to ensure that the right and left side by the middle of the blade flush. If it is not flush, the tipping face will not be flat and the cutter is very easy broken.
   
3. 
   Attention:the cutter will move when tight the screw.Main tips: slightly twist the screw,check whether the side of cutter and cutting mold is aligned。If it is not aligned, you can put the whole set on a flat platform, hit the cutter on the other side to make them aligned. And then tight the srew.
   
4. 
   After change the cutter, check all spaces between each parts,can be adjusted by M5 socket head cap screw before cutting mold.
   
5. 
   How to adjust the space of cutting mold and roller：To tighten the screws aside, while shaking layering ensure cone portion of the screw into the tapered layering pit. Should be appropriate to tighten the screws when fixed to the back 1/5 turns, then tighten the lock nut with a wrench.
   
6. 
   After the die cutter R must be parallel grooves, adjustable rear tip mold board two M8 hex adjustment screw, after the blade on the cutting die groove R parallel. Note R groove must retire over triangular groove
   
7. 
   installed, use the test results manually adjusted. Depress the clutch rotating cam pulley to stop playing in the highest position. Loosen the back seat board within two M6 hexagon screws, two M16 and then a little hollow screw top tight, and then tighten the screw above.
   
8. 
   After filling oil, then drive test run.
   
9. 
   In selecting the appropriate blade specification case, if found shoelace bad package, hexagonal screw within the adjustment screws 4 M8 front cover on the front and adjustable back within six M6 hexagon screws, so that a small amount of compression, careful not to crushed, before and after the adjustment is consistent die cutter.
   
10. 
    In the course of their work, such as found in the continuous lace cut or cut off at the burr, M6 adjustable fixed die cutter housing hex adjustment screw on the right side, the appropriate date
    
11. 
    As found in the sheet feeding operation is not normal, should check the sheet feeding mechanism, the pattern wheel and ratchet tensioner pulley fixing screw is loose, the fixed plate sheet feeding slot if there is debris cement, as found above, should loosen the screw to remove the debris, and then lock.
    
12. 
    After filling the lubricant class twice running.
    

Six,How to change the cutter：
1. disengaging the clutch.
2. Switch off the machine power.
3. Die loose tension spring to remove the body of the front cover and rear cover.
4. Die before first operation:
5. Remove the left before cutting die, essentials are: the front end of the die cutter lifted up until the die cutter can be located at the rear wheel is removed from the cam slot.
6. Replace the blade with a cutting die back in the reverse order, both the cam roller into the slot, then die cutter back into place.
7. Use the same approach to the right to replace mold.
8. Die again after the operation: the order is left and right.
9. Remove the left rear blade, replacement blades back.
10. Remove the right rear blade, replacement blades back.
11. Move Rule Die, blade gap verifying whether the side is wrong.
12. The two M8 hex adjustment screw until the blade is aligned in the end after the triangular groove on the die cutter.
13. Replace the two top cover.
14. regulate the cover and side layering screws.
15. The four were moved by hand die cutter, test the pressure of the gap.
16. After hanging Die tension spring, adjust the pressure (pressure strap crude demand bigger, smaller pressure tape Details)
17. In the clutch, hand drive cars, a test cycle (Note: To put the film and rope to test)
18. Note: Be sure to press the film (the side facing the natural bent after cutting die) to install, must not be reversed.
19. wrapped up judging quality of the installation.
20. If you have questions, you want to re-install.