2. Dastgox xaqida umumiy ma’lumot

6.5 Tishli g’ildiraklarning ilashish modulini aniqlash.

Ψ=8 Tishli g‘ildiraklarni enni hisobga oluvchi koeffitsent;
Y_Fi- Tish xolatini hisobga oluvchi koeffitsent 9-jadvaldan
Z_i= burovchi moment kata bo‘lgan tishlar soni.
M_Fi=M_imax*K_Fv*K_Fb
=309
S_F=2; K_Fe=1.03; K_Fc=1
G_Flimb=600 MPa
1- val uchun ilashish moduli
6.5.1) =1.75
2-val uchun ilashish moduli
6.5.2) =1.75
3-val uchun ilashish moduli
6.5.3) =2.25
4-val uchun ilashish moduli
6.5.4) =2.25
5-val uchun ilashish moduli
6.5.5) =3
m_o‘rt= =2.25
vallar uchun standart qatordan m=2.25 modulni tanlab oldim.
6.6 Tishli g’ildirakning konstuktiv o’lchamlari.
Bo’luvchi diametr – d_i=m*z
Tashqi diametr – d_ai=d_i+2m
Ichki diametr – d_fi=d_i-2.5m
Vallar orasidagi masofa – A_w=(d_k+d_sh)/2.

d₀₁=2.25 *45=101 d_a01=101+4.5=105.5 d_f01=101-5.6=95.4

d₀₂=2.25 *45=101 d_a02=101+4.5=105.5 d_f02=101-5.6=95.4
d₁=2.25 *46= 103 d_a1=103+4.5=107.5 d_f1=103-5.6=97.4
d₂=2.25 *44=99 d_a2 =99+4.5=103.5 d_f2=99-5.6=93.4
d₃=2.25 *44=99 d_a3=99+4.5=103.5 d_f3=99-5.6=93.4
d₄=2.25 *46=106 d_a4=103+4.5=107.5 d_f4=103-5.6=97.4
d₅=2.25 *41=92 d_a5=92+4.5=96.5 d_f5=92-5.6=86.4
d₆=2.25 *49=110 d_a6=110+4.5=114.5 d_f6=110-5.6=104.4
d₇=2.25 *45=101 d_a7=101+4.5=105.5 d_f7=101-5.6=95.4
d₈=2.25 *45=101 d_a8=101+4.5=105.5 d_f8=101-5.6=95.4
d₉=2.25 *44=99 d_a9=99+4.5=103.5 d_f9=99-5.6=94.4
d₁₀=2.25 *46=103 d_a10=103+4.5=107.5 d_f10=103-5.6=97.4
d₁₁=2.25 *53=119 d_a11=119+4.5=123.5 d_f11=119-5.6=113.4
d₁₂=2.25 *37=83 d_a12=83+4.5=87.5 d_f12=83-5.6=77.4
d₁₃=2.25 *44=99 d_a13=99+4.5=103.5 d_f13=99-5.6=93.4
d₁₄=2.25 *46=103 d_a14=103+4.5=107.5 d_f14=103-5.6=97.4
d₁₅=2.25 *37=83 d_a15=83+4.5=87.5 d_f15=83-5.6=77.4
d₁₆=2.25 *53=119 d_a16=119+4.5=123.5 d_f16=119-5.6=113.4
d₁₇=2.25 *30=67 d_a17=67+4.5=71.5 d_f17=67-5.6=61.4
d₁₈=2.25 *60=135 d_a18=135+4.5=139.5 d_f18=135-5.6=129.4
Shponka tanlash:
Qo`shimcha val uchun
Val diametri d=32 ga mos shponka razmerlarini jadvaldan tanlab olamiz
b=10
L=22 … 110
1-val uchun
Val diametri d=34 ga mos shponka razmerlarini jadvaldan tanlab olamiz
b=10
L=22 … 110
3-val uchun
Val diametri d=61 ga mos shponka razmerlarini jadvaldan tanlab olamiz
b=18
L=50 … 200




Podshipnik tanlash
Val diametriga mos podshivniklarni jadvaldan o’lchamlarini tanlab oldik
1 - val uchun
Val diametri d_v=25 bolgani uchun bunga standart qatordan
306 markali ya’ni ichki diametri 25 ga teng bo’lgan podshipnik tanlab oldik va o’lchamlarini tanlab oldik
d=30; D=62; B=16 r=1.5;
2-val uchun
Val diametri d_v=25 bolgani uchun bunga standart qatordan
306 markali ya’ni ichki diametri 25 ga teng bo’lgan podshipnik tanlab oldik va o’lchamlarini tanlab oldik
d=25; D=52; B=16; r=1.5;
3-val uchun
Val diametri d_v=28 bolgani uchun bunga standart qatordan
307 markali ya’ni ichki diametri 28 ga teng bo’lgan podshipnik tanlab oldik va o’lchamlarini tanlab oldik
d=28; D=52; B=21; r=2.5;
3-val uchun
Val diametri d_v=30 bolgani uchun bunga standart qatordan
308 markali ya’ni ichki diametri 30 ga teng bo’lgan podshipnik tanlab oldik va o’lchamlarini tanlab oldik
d=30; D=58; B=22; r=2.5;
4-val uchun
Val diametri d_v=46 bolgani uchun bunga standart qatordan
315 markali ya’ni ichki diametri 46 ga teng bo’lgan podshipnik tanlab oldik va o’lchamlarini tanlab oldik
d=46; D=70; B=37; r=3.5;